Which models does the Tube Ball Mills cover?
The Tube Ball Mills covers 4 models: 1456А, 1471, 2×10,5 m, 2×7 m. Former and renamed designations are listed in the models table on this page.
2026 · 4 models


Select a model to jump to its component table; former and renamed designations are listed under “Historical names / renamings”.
The numbers on the diagram correspond one to one with the rows below.
| No. | Component | Location | Applies to |
|---|---|---|---|
| 1 | Mill shell | Outer wall of the tube-mill drum | 2×7 m;2×10,5 m |
| 2 | Mill liner | Inner wall of both compartments | 2×7 m;2×10,5 m |
| 3 | Mill end cover | Left drum end | 2×7 m;2×10,5 m |
| 4 | Feed screw | Inside the left feed trunnion | 2×7 m;2×10,5 m |
| 5 | Compartment diaphragm | Between the coarse- and fine-grinding compartments | 2×7 m;2×10,5 m |
| 6 | Bearing liner | Inside the left trunnion bearing | 2×7 m;2×10,5 m |
| Component |
|---|
| Support rollers |
| Discharge bushing |
| Grinding balls |
| Tyre |
| Cylpebs |
| Guide blades |
| Loading cone |
| Gear-type coupling |
Models with the same components are grouped together; select a group to open its component table.
Models: 2×10,5 m, 2×7 m
| No. | Component |
|---|---|
| 1 | Mill Shell |
| 2 | Mill liner |
| 5 | Compartment partition plate |
| 6 | Model-specific component |
| Guide vane | |
| Model-specific component | |
| Gear-type coupling | |
| Model-specific component |
| No. | Component |
|---|---|
| 1 | Mill Shell |
| 2 | Mill liner |
| 3 | Mill End cover |
| 4 | Feed screw |
| 5 | Compartment partition plate |
| Model-specific component | |
| Discharge bushing | |
| Model-specific component | |
| Tyre | |
| Model-specific component |
| No. | Component |
|---|---|
| 1 | Mill Shell |
| 2 | Mill liner |
| 3 | Mill End cover |
| 4 | Feed screw |
| 5 | Compartment partition plate |
| Model-specific component | |
| Discharge bushing | |
| Model-specific component | |
| Tyre |
The Tube Ball Mills covers 4 models: 1456А, 1471, 2×10,5 m, 2×7 m. Former and renamed designations are listed in the models table on this page.
The Tube Ball Mills is also documented under these designations: 1456А, 1500×5600, МШ 1456, 1471, 1500×7100, МШ 1471, 2×10,5 m, 2×10,5, 2000×10500, МС 2×10,5, 2×7 m, 2000×7000.
The Tube Ball Mills is listed under the Strommashina brand. Period: 2026. Status: Historical model.
14 components are recorded, including: Mill Shell, Mill liner, Mill End cover, Feed screw, Discharge bushing, Tyre, Compartment partition plate, Guide vane and more. The full list with locations is in the components table on this page.
Envoyez-nous un plan ou un échantillon et indiquez le modèle d'équipement et le nom de la pièce.
Provide the equipment model, drawing for engineering review and quotation. If service life or wear is a concern, describe the operating conditions as well.
Ou contactez-nous directement : +86 156 3797 3199
zzx@anranst.com
ANRANST provides customers worldwide with engineering assessment, production at certified foundries to drawing, quality control and finished-part delivery for custom wear parts and industrial spares, with scope to support other custom industrial parts.
Veuillez fournir la marque de l’équipement, le modèle complet et le numéro de série, le nom de la pièce, sa référence ou le numéro du plan, l’indice de révision du plan, la quantité, les exigences relatives au matériau et les conditions de service. Si ces identifiants ne sont pas disponibles, envoyez des photographies et les dimensions principales.
Submit an Enquiry