METSO · Détails de la pièce

Blow Bar

Blow Bar

Identify Metso impact-crusher blow bars (e.g. NP series), check drawing revision, confirm materials/process and enquire. Keep bars, apron liners, frame liners and fasteners separate. Historic drawing samples on the generic blow-bar page are not current order promises. Generic page: /spare-parts/impact-crusher/blow-bar/

Équipements et modèles applicables

Identifiez le modèle installé et les dimensions clés, puis vérifiez la révision du plan et les interfaces physiques.

Equipment Series

Metso Impact Crusher

Models and Key Dimensions

Metso Nordberg NP13/NP15/NP20/NP1110/NP1213/NP1313/NP1315/NP1415/NP1520/NP1620/NP2023

Matériaux et procédés

Select the material grade and heat treatment for the operating conditions, processed material and equipment specifications. The options below are commonly used; confirm the final grade against the drawing and technical agreement.

Cr26 high-chromium cast iron (600-700 HB)

Select materials to suit OEM specifications and operating conditions; confirm the final grade and heat treatment against the drawing.

Martensitic Wear-Resistant Steel (450-550 HBW)

Select materials to suit OEM specifications and operating conditions; confirm the final grade and heat treatment against the drawing.

Ceramic MMC composite (60-65 HRC)

Select materials to suit OEM specifications and operating conditions; confirm the final grade and heat treatment against the drawing.

High-Manganese Steel Mn18Cr2 (220-240 HB)

Select materials to suit OEM specifications and operating conditions; confirm the final grade and heat treatment against the drawing.

Caractéristiques d'usure et remplacement

Modes d'usure et conseils d'entretien courants ; le cycle réel dépend des conditions, du matériau et des données de fonctionnement.

Modes d'usure courants

  • High-velocity material impact wears and rounds the ends
  • Impact initiates microcracks and drives their growth
  • Abrasion produces surface grooves
  • Ceramic inserts detach or fracture
Critères de remplacement

Assess the remaining blow bar section, cracks, ceramic insert condition and fastening against the maintenance requirements for the model. Replace immediately if a through-crack is found. Match replacement weights and maintain rotor balance as specified by the OEM.

Contrôle matière et procédé

Les exigences matière, traitement thermique, procédés composites et contrôles suivent le plan, les conditions et le contrôle technique.

Material Grade / Substrate

Cr26 high-chromium cast iron (600-700 HB) / martensitic wear-resistant steel (450-550 HBW) / ceramic MMC composite (60-65 HRC) / Mn18Cr2 high-manganese steel (220-240 HB)

Heat Treatment Condition

Follow the applicable standard for the material grade; confirm heat treatment and hardness requirements against the drawing

Composite / Hardfacing Requirements

Follow OEM design requirements; confirm any hardfacing or composite construction against the drawing

Dimensions and Inspection

Inspect key dimensions against the drawing for the OEM model details. Check mounting and sealing surfaces individually and perform UT/MT non-destructive testing on castings.

Des pièces de même nom peuvent ne pas être interchangeables selon le modèle, la révision du plan, les interfaces et les exigences matière. Avant fabrication, se baser sur le modèle complet, le numéro de série et les plans.

Send Your Wear Part Requirements

Provide the equipment model, drawing for engineering review and quotation. If service life or wear is a concern, describe the operating conditions as well.

Demander un devis

Ou contactez-nous directement : +86 156 3797 3199
zzx@anranst.com

Manufacturing Services in China

From Technical Assessment to Finished-Part Delivery

ANRANST provides customers worldwide with engineering assessment, production at certified foundries to drawing, quality control and finished-part delivery for custom wear parts and industrial spares, with scope to support other custom industrial parts.

Veuillez fournir la marque de l’équipement, le modèle complet et le numéro de série, le nom de la pièce, sa référence ou le numéro du plan, l’indice de révision du plan, la quantité, les exigences relatives au matériau et les conditions de service. Si ces identifiants ne sont pas disponibles, envoyez des photographies et les dimensions principales.

Submit an Enquiry