METSO · Détails de la pièce

Bowl Liner / Concave

Bowl Liner / Concave

Identify parts for Metso cone crushers, check models and drawing, confirm materials and processes, and submit an inquiry.

Équipements et modèles applicables

Identifiez le modèle installé et les dimensions clés, puis vérifiez la révision du plan et les interfaces physiques.

Equipment Series

Metso Cone Crushers

Models and Key Dimensions

Metso HP Series (HP100-HP800), GP Series (GP100-GP550), MP Series (MP800-MP1000) and Omnicone 1560

Matériaux et procédés

Select the material grade and heat treatment for the operating conditions, processed material and equipment specifications. The options below are commonly used; confirm the final grade against the drawing and technical agreement.

High-Manganese Steel Mn18Cr2

Solution-treated and water-quenched high-manganese steel; surface work hardening depends on impact and contact loading. Verify initial hardness against the material standard and drawing.

High-Manganese Steel Mn13Cr2

Standard manganese steel, a cost-effective option for crushing medium-hard materials

Metso XT710

Specify independently manufactured replacement materials through the agreed specification, heat certificate and test results. Where an OEM commercial material is cited for identification, label it as an original-part reference and confirm ANRANST supply material separately without assuming equivalence or a life multiplier.

Metso MX composite wear material

A manganese steel matrix with wear-resistant inserts. Metso states that its MX for cones products can achieve up to 2 times the wear life of standard manganese liners under suitable conditions. This is not a service-life guarantee for parts supplied through this website.

High-manganese steel Mn22Cr2

Candidate high-manganese steel; select for actual impact, abrasion and drawing requirements. Manganese content alone does not determine service life.

Caractéristiques d'usure et remplacement

Modes d'usure et conseils d'entretien courants ; le cycle réel dépend des conditions, du matériau et des données de fonctionnement.

Modes d'usure courants

  • The parallel chamber zone typically wears fastest; the liner profile gradually flattens and the product becomes coarser
  • Material compression causes surface fatigue spalling and fish-scale wear patches
  • Wear at the liner and adjustment ring mating surfaces increases installation clearance
  • Wear of trapezoidal rack teeth, where fitted, reduces locking force
Critères de remplacement

Determine replacement timing from the model-specific maintenance manual and actual worn profile. Stop and inspect if CSS adjustment cannot correct abnormal product size or if through-cracks appear. Plan mantle and concave replacement together according to the chamber profile and wear condition.

Contrôle matière et procédé

Les exigences matière, traitement thermique, procédés composites et contrôles suivent le plan, les conditions et le contrôle technique.

Material Grade / Substrate

High-manganese steels Mn18Cr2 and Mn13Cr2, Metso XT710 and other specified grades

Heat Treatment Condition

Solution heat treatment with water quenching. Final hardness and microstructure must meet the drawing and agreed technical specification.

Composite / Hardfacing Requirements

Metso MX composite liners use a manganese steel matrix with wear-resistant inserts rather than hardfacing. Replace the complete liner; localized repair is not applicable.

Dimensions and Inspection

Verify critical dimensions against the drawing for the OEM model details, including fits, sealing surfaces and oil groove locations. Select nondestructive testing methods for the material, part geometry and technical agreement; MT applies only to suitably magnetizable ferromagnetic materials. Check copper alloy bushing hardness and uniformity as specified in the drawing.

Des pièces de même nom peuvent ne pas être interchangeables selon le modèle, la révision du plan, les interfaces et les exigences matière. Avant fabrication, se baser sur le modèle complet, le numéro de série et les plans.

Send Your Wear Part Requirements

Provide the equipment model, drawing for engineering review and quotation. If service life or wear is a concern, describe the operating conditions as well.

Demander un devis

Ou contactez-nous directement : +86 156 3797 3199
zzx@anranst.com

Manufacturing Services in China

From Technical Assessment to Finished-Part Delivery

ANRANST provides customers worldwide with engineering assessment, production at certified foundries to drawing, quality control and finished-part delivery for custom wear parts and industrial spares, with scope to support other custom industrial parts.

Veuillez fournir la marque de l’équipement, le modèle complet et le numéro de série, le nom de la pièce, sa référence ou le numéro du plan, l’indice de révision du plan, la quantité, les exigences relatives au matériau et les conditions de service. Si ces identifiants ne sont pas disponibles, envoyez des photographies et les dimensions principales.

Submit an Enquiry